Laptop Hardware
The XO-1 laptop is a central
focus of One Laptop Per Child.
After three years of
development, it is in mass
production, with hundreds of
thousands of units deployed in
the field, and thousands more
with developers and for testing
in schools all over the world.
Specifications
The definitive laptop
specification is only available in
PDF format. This page attempts
to accurately reflect that
information. Note: this is the
specification of the laptop
currently in production. The
specification for the earlier CL1
version (with the wide dual-
mode touchpad) is here.
Physical dimensions
Approximate dimensions:
242mm × 228mm × 32mm (see
drawing to the right for detailed
dimensions)
Approximate weight:
XO laptop with LiFePO4 battery:
1.45KG (~3.20lbs);
XO laptop with NiMH battery:
1.58KG (~3.48lbs);
Configuration: Convertible
laptop with pivoting, reversible
display; dirt- and moisture-
resistant system enclosure; no
fan.
Core electronics
A photo of the XO Motherboard
is available, with or without
annotations.
CPU: x86-compatible processor
with 64KB each L1 I and D
cache; at least 128KB L2 cache;
Datasheet
CPU clock speed: 433 Mhz;
i586 instruction set (including
MMX and 3DNow! Enhanced)
with additional Geode-specific
instructions
Companion chips: PCI and
memory interface integrated
with CPU;
North Bridge: PCI and Memory
Interface integrated with Geode
CPU ( info )
South Bridge: datasheet
Errata
Graphics controller: Integrated
with CPU; unified memory
architecture;
Embedded controller: ENE
KB3700 or ENE KB3700B;
Embedded Controller: ENE
KB3700
DRAM memory: 256 MiB dynamic
RAM; data rate: dual-
DDR333-166Mhz;
BIOS: 1024KiB SPI-interface flash
ROM;
Open Firmware used to load the
operating system;
Mass storage: 1024 MiB SLC
NAND flash; (a few "Red XOs"
have been built with 2048 MiB
of flash)
Drives: No rotating media.
CAFE ASIC (camera- and flash-
enabler chip provides high-
performance camera, NAND
FLASH and SD interfaces); Marvell
88ALP01: CAFE Specification
plus presence detect erratum
Display
Main article: Display
Liquid-crystal display: 7.5” dual-
mode TFT display;
Viewing area: 152.4 mm × 114.3
mm;
Two "modes" depending on
lighting conditions:
(1) Grayscale (B&W) reflective
mode: for outdoor use —
sunlight-readable; primarily lit
from the front by ambient light;
high-resolution (200 DPI),
1200(H) × 900(V) grayscale
pixels; power consumption 0.1 –
0.2Watts;
(2) Color, backlight mode: for
indoor use; primarily lit from
behind by the LED backlight;
built in sub-pixel sampling of the
displayed color information
results in a perceived resolution
of approximately 984(H) ×
738(V) ; power consumption
0.2–1.0Watts;
The display-controller chip
(DCON) with memory that
enables the display to remain
live with the processor
suspended. The DCON also
formats data for the display.
This Liquid-crystal display is the
basis of our extremely low
power architecture. The XO is
usable while the CPU and much
of the motherboard is regularly
turned off (and on) so quickly
that it's imperceptible to the
user. Huge power savings are
harvested in this way (e.g. by
turning stuff on the
motherboard off when it's not
being used (if even for a few
seconds), while keeping the
display on).
Note: web browser images are
currently scaled up so that an
image of very roughly [800 ×
600] fills up the browser
window.
Integrated peripherals
Keyboard: 80+ keys, 1.0mm
stroke; sealed rubber-membrane
key-switch assembly;
Keyboard Layouts
Layout pictures: English, Arabic,
Thai, West African (Nigeria),
Portuguese, Spanish, Amharic,
French, Urdu, Cyrillic, Turkish
(not final), Nepali, Mongolian,
Kazakh, Devanagari, Uzbek,
Pashto, Dari, Pulaar (Fula), Italian
Gamepad: Two sets of four-
direction cursor-control keys;
Touchpad: Capacitance touchpad
ALPS Electric Dual capacitance/
resistive touchpad;
Audio: AC’97 compatible audio
subsystem; Internal stereo
speakers and amplifier; internal
monophonic microphone; jacks
for external headphones or
microphone;
Analog Devices AD1888 and
Analog Devices SSM2302 for
audio amplification
Camera: integrated color video
camera; 640 x 480 resolution at
30 FPS; independent (and
undefeatable by software)
display of microphone and
camera recording status; the
camera and device driver
support disabling AGC and
automatic color balancing, to
enable its use as a photometric
sensor for educational
applications;
Omnivision OV7670
Wireless Networking: Integrated
802.11b/g (2.4GHz) interface;
802.11s (Mesh) networking
supported; dual adjustable,
rotating antennas support
diversity reception; capable of
mesh operation when CPU is
powered down;
Marvell Libertas wireless chipset,
88W8388 controller and
88W8015 radio
Status indicators: Power,
battery, and WiFi (2), visible
with lid open or closed;
Microphone In-Use, and Camera
In-Use, visible when lid is open.
External connectors
DC power: 6mm (1.65mm center
pin) connector; 11 to 18 V input
usable, –32 to +40V input
tolerated; power draw limited
to 18 W; - see power connector
dimensions at Battery and
power.
Headphone output: standard
3.5mm 3-pin switched stereo
audio jack;
Microphone input: standard
3.5mm 2-pin switched mono
microphone jack; selectable 2V
DC bias; selectable sensor-input
mode (DC or AC coupled);
USB: Three Type-A USB 2.0
connectors; Up to 1A power
supplied (total);
Flash Expansion: SD Card slot.
Battery
Pack type: 2 or 4 cells LiFePO4;
or 5 cells NiMH, approx. 6V series
configuration (subject to
change);
Capacity: 16.5 Watt-hours
(NIMH), 22 Watt-hours (LiFeP);
Fully-enclosed “hard” case; user
removable;
Electronics integrated with the
pack provide:
Identification;
Battery charge and capacity
monitoring chip ( Maxim DS2756
data sheet);
Thermal and over-current
sensors along with cutoff
switch to protect battery;
Minimum 2,000 charge/
discharge cycles (to 50%
capacity of new).
Power Management will be
critical
See Laptop Batteries or more
information.
BIOS/loader
Open Firmware (including
hardware initialization and fast
resume).
Panasonic ML1220 battery
Environmental
specifications
Temperature: UL certification
planned to 45C in Q32007,
pending 50C certification in
mid-2008;
Humidity: UL certification
planned to IP42 (perhaps
higher) when closed, the unit
should seal well enough that
children walking to and from
school need not fear rainstorms
and dust;
Maximum altitude: –15m to
3048m (14.7 to 10.1 PSIA)
(operating), –15m to 12192m
(14.7 to 4.4 PSIA) (non-
operating);
Shock 125g, 2ms, half-sine
(operating) 200g, 2ms, half-sine
(non-operating);
Random vibration: 0.75g zero-
to-peak, 10Hz to 500Hz, 0.25
oct/min sweep rate (operating);
1.5g zero-to-peak, 10Hz to
500Hz, 0.5 oct/min sweep rate
(nonoperating);
2-3mm plastic walls (1.3mm is
typical for most systems).
Regulatory
requirements
The usual US and EU EMI/EMC
(electromagnetic-interference
and electromagnetic-
compatibility) requirements will
be met;
The laptop meets IEC 60950-1,
EN 60950-1, and CSA/UL 60950-1
specifications. It also complies
with UL 1310 and UL 498. In
order to guarantee the safety of
children using the laptop, it
passes ASTM F 963;
The external power adapter
complies with IEC, EN, and CSA/
UL 60950-1;
The removable battery pack
complies with IEC, EN, and CSA/
UL 60950-1 and UL 2054;
RoHS (Restriction of Hazardous
Substances Directive – EU)
compliant.
Laptop Development
Schedule
On April 15, 2006, the first
prototypes of the XO, the A1
prototype boards, were first
powered on. Development
continued with the B1, the first
complete prototype laptop, in
November of 2006. The B2
laptops were the first to
incorporate the CaFE chip, and
was produced in small quantities
for initial trials in January 2007.
In April of 2008 the design was
refreshed with a faster
processor and more memory/
NAND flash. The B3 prototypes
were the first test of this
design. Slight refinements were
incorporated into the B4,
manufactured in June 2008,
which is very similar to the
production version of the
laptop. Finally, mass production
started in November 2007 with
the C2 version.
Serial Adapter
In order to conserve parts/
space, while the motherboard
does provide two serial ports
for debugging (one populated in
production), it does not provide
voltage translators to fully
implement the RS-232 protocol.
Thus a 3.3V TTL to RS-232 (or
USB) Adapter is needed.
No comments:
Post a Comment