A PCB is a printed circuit board,
also known as a printed wiring
board. It is used in electronics to
build electronic devices. A PCB
serves two purposes in the
construction of an electronic
device; it is a place to mount the
components and it provides the
means of electrical connection
between the components.
A PCB starts out as a thin, non-
conducting sheet of material.
The most common material used
is a glass fiber epoxy laminate
material. A thin layer of copper
is then chemically deposited on
each side of this material.
The next step is to "print" the
connection diagram onto the
PCB. The connection diagram is
the wiring required to connect
the components. In the very
early days of electronics, these
connections were in fact done
with wires. This is the reason
PCBs are also sometimes
referred to as printed wiring
boards. The "printing" is usually
done by photographically
transferring the image to the
PCB. This image is "printed" with
an acid resistant material.
Next, the PCB is put into an acid
bath. The acid bath removes the
copper from the board,
excepting the areas protected
by the resistant material. This
process leaves the connections
or wiring "printed" on the PCB.
Next, holes are drilled in the
board to allow the components
to be mounted to the PCB and
the PCB itself to be mounted to
the case protecting the
electronics. Finally, a protective
coating is applied to the board
to prevent corrosion of the
copper traces.
The above process describes
what is referred to as a doubled
sided or two layer PCB. It is
possible to make PCBs of almost
any number of layers by
repeating the process above and
laminating the resulting PCBs
into a single PCB. The PCB inside
of the computer on which you
are reading this document is a
minimum four layer PCB and
more likely to be an eight or
even 12 layer PCB.
It is also more common now for
parts to be soldered directly to
the board, eliminating the need
for holes into which leads
(wires) from the components
must be inserted. A component
soldered to the board is logically
called a surface mount
component, and the PCB is a
surface mount PCB. This
technique allows a large increase
in the number of components to
be mounted on the same PCB, or
the same number of
components to be mounted on a
much smaller PCB. However,
surface mounting also requires
better quality control on the
manufacture of the PCB.
A PCB is now used in almost
every electronic product
available. It is by far the most
common method currently used
to connect and assemble the
components of almost any
electronic device.
A
A
VIKAS WORLD POWERD by VIKAS
Nautral Incrodible of Different Hilarious Important
zone
April 25, 2010
A motherboard is the underlying
circuit board of a computer. The
central processing unit (CPU),
Random Access Memory (RAM),
hard drive(s), disk drives and
optical drives are all plugged
into interfaces on the
motherboard. A video interface
and sound card can be
optionally built-in or added.
A motherboard can come in
many configurations to fit
different needs and budgets. At
its most basic, it comes with
several interfaces for necessary
components and a BIOS chip set
to control setup of the
motherboard. Many computer
enthusiasts favor one type of
BIOS over another and will
choose a motherboard partially
based on the BIOS manufacturer.
For example, many gamers
prefer the Nvidia BIOS as it is
rated as one of the best for
graphics applications.
An equally important feature of
the motherboard is the type of
CPU it will support. Some
motherboards support AMD
CPUs, while others support Intel
processors. Within the
manufacturer's categories, there
are different grades of CPUs. An
AMD 64-bit processor requires a
different CPU socket than an
AMD 32-bit processor. Thus, if
purchasing parts independently,
one must decide on the CPU
before choosing the
motherboard to ensure
compatibility.
Another important
consideration is the amount and
type of RAM the motherboard
will support. It is always best to
buy a board that supports more
RAM than currently needed. If
new technology for RAM chips
is available, getting a board that
supports the newer chips will
help future-proof the
investment.
The number of PCI slots varies
from motherboard to
motherboard, as do other
interfaces like the number of
SATA ports, differing RAID
abilities, and USB and Firewire
ports. As mentioned prior, sound
and video capability might be
built-in, though purists generally
prefer to disable internal video
and sound and add superior
third party cards. A
motherboard also comes in one
of a few standard footprints or
sizes. This figures in when
purchasing the system case.
Along these lines, many
motherboard manufacturers
recommend particular power
supplies that have been tested
with the board.
Though building a computer
used to be somewhat
challenging, today most
motherboards are color-coded
with controllers built-in, making
it very easy to build a computer
from scratch. The only time
consuming aspect is
investigating which hardware
will best suit your needs while
fitting into your budget. Once
the CPU and motherboard is
chosen, RAM is somewhat
determined by the board itself.
Hard drives, an optical disk, a
video card, a sound card and a
floppy round out the basics.
There are many technical
websites that review new
products. If you are in the
market for a motherboard, you
might want to spend some time
researching your choices. A
good motherboard will be easy
to set up, will support all of the
hardware you desire, and will
serve your needs into the
foreseeable future. A
motherboard that supports the
newest technology available will
be more expensive than boards
that are already close to
obsolete.
Often older motherboards are
blown out at reduced prices,
complete with a CPU, and in
some instances a case with
power supply. These
"barebones" systems are meant
to be built from that point up
with other components of your
choosing. Though you can get a
good deal on such a system, in
some cases the motherboard
included does not support one
or more newer technologies,
and therefore lacks the
flexibility or longevity of a more
current model. Therefore, be
sure the system supports all of
the technologies you desire
before making a purchase.
circuit board of a computer. The
central processing unit (CPU),
Random Access Memory (RAM),
hard drive(s), disk drives and
optical drives are all plugged
into interfaces on the
motherboard. A video interface
and sound card can be
optionally built-in or added.
A motherboard can come in
many configurations to fit
different needs and budgets. At
its most basic, it comes with
several interfaces for necessary
components and a BIOS chip set
to control setup of the
motherboard. Many computer
enthusiasts favor one type of
BIOS over another and will
choose a motherboard partially
based on the BIOS manufacturer.
For example, many gamers
prefer the Nvidia BIOS as it is
rated as one of the best for
graphics applications.
An equally important feature of
the motherboard is the type of
CPU it will support. Some
motherboards support AMD
CPUs, while others support Intel
processors. Within the
manufacturer's categories, there
are different grades of CPUs. An
AMD 64-bit processor requires a
different CPU socket than an
AMD 32-bit processor. Thus, if
purchasing parts independently,
one must decide on the CPU
before choosing the
motherboard to ensure
compatibility.
Another important
consideration is the amount and
type of RAM the motherboard
will support. It is always best to
buy a board that supports more
RAM than currently needed. If
new technology for RAM chips
is available, getting a board that
supports the newer chips will
help future-proof the
investment.
The number of PCI slots varies
from motherboard to
motherboard, as do other
interfaces like the number of
SATA ports, differing RAID
abilities, and USB and Firewire
ports. As mentioned prior, sound
and video capability might be
built-in, though purists generally
prefer to disable internal video
and sound and add superior
third party cards. A
motherboard also comes in one
of a few standard footprints or
sizes. This figures in when
purchasing the system case.
Along these lines, many
motherboard manufacturers
recommend particular power
supplies that have been tested
with the board.
Though building a computer
used to be somewhat
challenging, today most
motherboards are color-coded
with controllers built-in, making
it very easy to build a computer
from scratch. The only time
consuming aspect is
investigating which hardware
will best suit your needs while
fitting into your budget. Once
the CPU and motherboard is
chosen, RAM is somewhat
determined by the board itself.
Hard drives, an optical disk, a
video card, a sound card and a
floppy round out the basics.
There are many technical
websites that review new
products. If you are in the
market for a motherboard, you
might want to spend some time
researching your choices. A
good motherboard will be easy
to set up, will support all of the
hardware you desire, and will
serve your needs into the
foreseeable future. A
motherboard that supports the
newest technology available will
be more expensive than boards
that are already close to
obsolete.
Often older motherboards are
blown out at reduced prices,
complete with a CPU, and in
some instances a case with
power supply. These
"barebones" systems are meant
to be built from that point up
with other components of your
choosing. Though you can get a
good deal on such a system, in
some cases the motherboard
included does not support one
or more newer technologies,
and therefore lacks the
flexibility or longevity of a more
current model. Therefore, be
sure the system supports all of
the technologies you desire
before making a purchase.
Subscribe to:
Posts (Atom)